Xingtai Kangyong Machinery Manufacturing Co., Ltd

Home >> News >>Industry News >> Design of Water Circulation System for Car Washing Machine: Technical Path from Wastewater Treatment to Resource Utilization
Details

Design of Water Circulation System for Car Washing Machine: Technical Path from Wastewater Treatment to Resource Utilization

Introduction

The shortage of water resources and the tightening of environmental regulations are the two major challenges facing the car washing machine industry. The water circulation system not only saves water but also reduces wastewater discharge by recycling, treating, and reusing car wash wastewater, which meets the requirements of sustainable development. This article will explore the technical path of the water circulation system for car washing machines from three aspects: wastewater characteristic analysis, treatment process selection, and system design points.


1、 Characteristics and treatment difficulties of car wash wastewater

Analysis of wastewater composition

Car wash wastewater mainly contains the following pollutants:

Suspended solids (SS): sediment, dust, car paint fragments, etc., with a concentration of up to 500-2000mg/L.

Oil: lubricating oil, rust proof oil, etc., with a concentration of 50-200mg/L.

Surfactant (LAS): A foaming agent in car wash fluid, with a concentration of 10-50mg/L.

Heavy metals: Lead, copper, etc. produced by brake pad wear, with low concentration but toxicity.

Dealing with difficulties

The particle size distribution of suspended solids is wide: from micron sized car paint fragments to millimeter sized sediment, multi-stage filtration is required.

Oil emulsification: Surfactants in car wash fluid emulsify oil, making it difficult to separate by gravity.

Bacterial growth: Organic matter in wastewater provides nutrients for bacteria, which can easily produce odors and corrode pipelines.

2、 The core treatment process of water circulation system

Preprocessing stage

Grid slag removal: Remove large suspended particles through coarse grids (aperture 5-10mm) and fine grids (aperture 1-5mm).

Regulating tank: Balance the quality and quantity of wastewater to avoid sudden changes in the load of subsequent treatment units.

Oil water separation: Use inclined plate oil separators or air flotation devices to remove floating oil and reduce oil concentration to below 50mg/L.

Main processing stage

Coagulation precipitation: PAC (polyaluminum chloride) and PAM (polyacrylamide) are added to coagulate suspended solids into large particles, which are removed through a sedimentation tank.

Filtration: Multiple media filters (quartz sand+activated carbon) or membrane filtration (ultrafiltration, nanofiltration) are used to further remove suspended solids and organic matter.

Disinfection: Kill bacteria through ultraviolet or ozone oxidation, prevent pipeline corrosion and odor generation.

Deep processing stage (optional)

Reverse osmosis (RO): removes soluble salts, and the produced water can be reused in high-pressure water systems or for household use.

Ion exchange: further reduce heavy metal concentration to meet reuse standards.

3、 Design points of water circulation system

System Process Design

The typical process of a water circulation system is:

Car wash wastewater → Grille → Regulating tank → Oil water separation → Coagulation sedimentation → Filtration → Disinfection → Reuse

During design, process parameters need to be adjusted based on wastewater quality and reuse standards. For example, if the recycled water is only used for initial washing, the reverse osmosis process can be omitted; If used in high-pressure water systems, an RO device needs to be added.

Equipment selection and matching

Sedimentation tank: The recommended surface load rate is 0.8-1.2m 3/(m 2 · h), with a residence time of ≥ 1.5h.

Filter: The recommended filtration rate for multi-media filters is 8-10m/h, and the membrane filtration flux should be selected according to the membrane material (such as ultrafiltration flux of 50-80L/(m 2 · h)).

Disinfection equipment: The UV dose should be ≥ 30mJ/cm 2, and the recommended ozone dosage is 3-5mg/L.


Technical Support: 网站建设 | Admin Login
seo seo